Sikasil® Pool
Sikasil® Pool is a one component, neutral curing silicone sealant for use in swimming pools and permanently wet areas.
- Very good water resistance
- High chlorine resistance
- Movement capability ±25 %
- Very good resistance to fungal attack
- Neutral curing, non-corrosive
- High elasticity and flexibility
Usage
Sealing joints around swimming pools:- Areas under permanent water immersion
- Wet areas between tiles, concrete, glass and metals.
- For interior and exterior use
Advantages
- Very good water resistance
- High chlorine resistance
- Movement capability ±25 %
- Very good resistance to fungal attack
- Neutral curing, non-corrosive
- High elasticity and flexibility
Packaging
300 ml cartridges, 12 cartridges per box
Colour
White, grey, transparent
Product Details
Product declaration
EN 15651-1: Sealants for non-structural use in joints in buildings - Facade elements
Composition
Neutral curing silicone
Shelf life
Sikasil® Pool has a shelf life of 12 months from the date of production, if it is stored properly in undamaged, original, sealed packaging, and if the storage conditions are met.
Storage conditions
Sikasil® Pool shall be stored in dry conditions, protected from direct sunlight and at temperatures between +5 °C and +25 °C.
Density
~1,05 kg/l | (ISO 1183-1) |
Shore A hardness
~20 (after 28 days) | (ISO 868) |
Tensile strength
~1,5 N/mm2 | (ISO 8339) |
Secant tensile modulus
~0,30 N/mm2 at 100 % elongation (23 °C) | (ISO 8339) |
Movement capability
± 25 % | (ISO 9047) |
Elastic recovery
> 90 % | (ISO 7389) |
Tear propagation resistance
~4,0 N/mm | (ISO 34) |
Service temperature
−40 °C to +80 °C
Chemical resistance
Resistant to chlorine and cleaning chemicals. Contact Sika Technical Services for additional information.
Joint design
The joint dimensions must be designed to suit the movement capability of the sealant. The joint width must be a minimum of 10 mm and a maximum of 15 mm.
The joint depth must be a minimum of 6 mm and a maximum of 10 mm.
For larger joints, contact Sika Technical Services for additional information.
Application
Sag flow
< 2 mm (20 mm profile, 23 °C) | (ISO 7390) |
Ambient air temperature
+5 °C min. / +40 °C max.
Substrate temperature
+5 °C min. / +40 °C max. Minimum +3 °C above dew point temperature
Backing material
Use closed cell, polyethylene foam backing rod
Curing rate
~2,0 mm/24 hours (+23 °C / 50 % r.h.) | (CQP* 049-2) * Sika Corporate Quality Procedure |
Skinning time
~5 minutes (+23 °C / 50 % r.h.) | (CQP 019-1) |
Consumption
Joint width [mm] | Joint depth [mm] | Joint length [m] per 300 ml cartridge |
10 | 8 | 3.5 |
15 | 10 | 2 |
SUBSTRATE PREPARATION
The substrate must be sound, clean, dry and free of all contaminants such as dirt, oil, grease, cement laitance and old sealants which could affect adhesion of the sealant. The substrate must be of sufficient strength to resist the stresses induced by the sealant during movement.
Removal techniques such as wire brushing, grinding, grit blasting or other suitable mechanical tools can be used.
All dust, loose and friable material must be completely removed from all surfaces before application of any activators, primers or sealant.
Sikasil® Pool adheres without primers and/or activators.
For optimum adhesion and joint durability the following priming and/or pre-treatment procedures must be followed:
Non-porous substrates
Aluminium, anodised aluminium, stainless steel, PVC, galvanised steel, powder coated metals or glazed tiles. Slightly roughen surface with a fine abrasive pad. Clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth.
Before sealing, allow a waiting time of > 15 minutes (< 6 hours).
Other metals, such as copper, brass and titanium-zinc, clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth. After a waiting time of > 15 minutes (< 6 hours). Apply Sika® Primer-3 N applied by brush. Before sealing, allow a waiting time of > 30 minutes (< 8 hours)
PVC has to be cleaned and pre-treated using Sika® Primer-215 applied with a brush. Before sealing, allow a waiting time of > 30 minutes (< 8 hours).
Glass must be cleaned with Isopropanol before application
Porous substrates
Concrete and unglazed tiles must be primed using Sika® Primer-3 N applied by brush. For more details such as application and flash-off times, refer to the most recent Product Data Sheet of the respective pre-treatment product.
Before sealing, allow a waiting time of > 30 minutes (< 8 hours).
Adhesion tests on project specific substrates must be performed and procedures agreed with all parties before full project application.
MIXING
1-part ready to use
CLEANING OF EQUIPMENT
Clean all tools and application equipment immediately after use with Sika® Remover-208. Hardened material can only be removed mechanically. For cleaning skin, use Sika® Cleaning Wipes-100.